Copper, brass, aluminiumRadiators and heater cores
Copper and brass radiators grade differently from aluminium ones, so keep them apart. Drain the coolant and cut off steel brackets and plastic tanks.
Taren Point 2229 · workshops, trade and showrooms
Scrap metal from Taren Point repair shops, trade counters, warehouses and homes, collected by truck or on-site bin from our Mortdale yard. Each grade is weighed where you can watch and paid on the spot.


Short answer
Yes. We collect scrap metal from Taren Point workshops, trade counters, showrooms and homes, by truck or on-site bin from our Mortdale yard. Copper, brass, aluminium and cable are collected free, steel-heavy loads may carry a fee we quote first, and every grade is weighed in front of you and paid on the spot by non-cash payment.
Scrap metal Taren Point
Taren Point is the first part of the Sutherland Shire you reach after crossing the Captain Cook Bridge from Sans Souci. The bridge spans the Georges River close to Botany Bay and lands directly on Taren Point Road, with Woolooware Bay to the east. A 2022 Sutherland Shire Council planning proposal put the suburb's industrial and urban services land at around 143 hectares, with less than one hectare undeveloped.
The same planning work found auto repairs, hardware and trade services still prominent along Taren Point Road, beside smash repairers, car yards, light industry, warehouses and plant and landscape suppliers. The eastern side has become a home maker precinct of large showrooms, and bigger industrial sites sit back from the main road. Each of those businesses makes scrap in its own way.
Trucks and bins come from our yard at 18 Barry Ave, Mortdale, on the St George side of the river. Taren Point Road is an arterial State road, and council's reports describe it as heavily used and congested at peak times, which shapes when we book the bigger lifts.
Commercial scrap metal removal
What the local business mix tends to produce, and how each load is usually set up. A photo of your own pile is always the first step.
| Business | Metal that usually comes out | How it is normally handled |
|---|---|---|
| Mechanical and auto repair workshops | Radiators, alternators, starter motors, batteries, brake rotors, exhaust steel | Wheelie or forklift bin for non-ferrous, batteries on a pallet, steel apart |
| Smash repairers | Steel and aluminium panels, bumper reinforcements, damaged radiators and condensers | Refrigerant recovered first, then a skip swapped as it fills |
| Hardware and trade supply counters | Damaged copper pipe, brass fittings, cable drum ends, bent steel stock | Separate cages so copper, brass and cable keep their grades |
| Home maker showrooms | Steel shelving and display racking, aluminium shopfront frames, aircon after a refit | Night or weekend pick ups so the floor stays open |
| Warehouses and distribution sites | Pallet racking, damaged cages, steel strapping, lead-acid forklift batteries | Hooklift or Marrell skip bins, any steel fee quoted first |
| Light industry and fabrication | Steel, stainless and aluminium offcuts, electric motors, compressors | Forklift bins by grade, collected when you call |
We do not take gas cylinders, radioactive material or general electronics.
Automotive and workshop scrap
Workshop metal is easy to lose in a skip of oily rags and cardboard. Kept dry and separate, most of it has value on the scale.
Copper, brass, aluminiumCopper and brass radiators grade differently from aluminium ones, so keep them apart. Drain the coolant and cut off steel brackets and plastic tanks.
MotorsThe copper windings give these their value. A crate of them weighs in as electric motors, a separate line from plain steel.
LeadCar, truck, forklift and boat batteries. Stand them upright on a pallet away from rain and drains, never loose in a bin.
CompressorsFrom vehicles, coolrooms and building plant, accepted once a licensed technician has recovered the refrigerant.
AluminiumWheels with tyres and weights removed, cylinder heads and gearbox housings. Take off steel bolts and brackets and the aluminium is worth more.
Car aircon, coolrooms and building plant
Any unit still holding refrigerant gas must be emptied by a licensed technician before it is scrapped, whether it came from a car or a rooftop.
The Australian Refrigeration Council, which runs the ARCtick licence scheme, says a Refrigerant Handling Licence is needed to decommission equipment that still contains gas. Its advice to smash repairers is direct: vehicles you repair, dismantle or recycle probably still hold refrigerant, and it should be recovered before the parts are recycled.
For a Taren Point repair shop, a licensed automotive aircon technician degasses the condenser or compressor before it goes in our bin, and coolroom plant needs a licensed refrigeration technician. For split, ducted and VRV systems, rooftop package units or chillers from a showroom or warehouse refit, we can arrange certified refrigerant recovery as part of the removal through our commercial aircon recycling service.

A-K Scrap Metal · SydneyCommercial bins in Taren Point
Some sites along Taren Point Road are strata-titled units with little spare floor space; others are much larger industrial sites. The bin should suit both.
Before the truck arrives
A few details from you make the visit shorter and the payment higher.
Through traffic between the bridge and the rest of the Shire backs the road up at peak times. Book outside the morning and evening rush, or after hours for a strip-out.
Council notes overhead powerlines and narrow footpaths along Taren Point Road. If metal must be lifted from the street frontage by hiab or crane, tell us, so we can plan where the truck stands or use a rear yard.
A mixed bin tends to be graded down, so a few separate bins usually pay for themselves. Our guide on how to prepare scrap metal for sale shows how to sort a workshop pile.
Beyond the workshop
With the Georges River on one side and Woolooware Bay on the other, Taren Point is a waterfront suburb, and boat work makes its own scrap: aluminium trailers, stainless and brass deck fittings, outboard parts, copper cable and marine batteries. Drain fuel and oil first, strip off timber and fibreglass, and keep stainless away from plain steel. A magnet helps: steel grabs it hard, most stainless barely holds it.
We cannot take gas cylinders. Community Recycling Centres accept household quantities of gas bottles free, but the NSW EPA states that businesses are not eligible to use them and should contact a waste disposal service directly. For residents, Sutherland Shire Council said in its 2026 consultation that the Shire had no Community Recycling Centre yet and that sites at Kurnell and Kareela were being considered, so check the council's website for the current position.
Taren Point's residential streets follow the river side of the suburb, and those homes produce the usual renovation scrap: hot water systems (disconnected by a licensed plumber first), old taps and aluminium ladders. Our Sutherland Shire pick up page covers household collections across the region, and businesses with a second site can see scrap metal pick up in Kirrawee.
Google reviews
I cannot recommend Mo and the team at A-K highly enough. Not only did I have a difficult job, but I also had to make an unexpected short notice change to the timings and they were accommodating and understanding of my situation. They were honest, prompt and great value for money!
Fifteen out of 10! Picked up my scrap aluminium at premium prices! Extremely quick, weight with photos. And lightning fast payment. Thanks to the guys for a professional service. I'm a printing company in Alexandria.
Wouldn't recommend anyone else except these guys, they offer the best rates and best service! Props to Moe and Joe for their hard work and never disappointing us.
ExcellentBased on 61 Google reviews
Sources
The planning, waste and licensing pages behind the local detail on this page.
Taren Point questions
No. Our yard and factory are at 18 Barry Ave, Mortdale, and we come to Taren Point by truck or leave a bin with you. To bring a ute or trailer load in yourself, drop it at Mortdale during factory hours and we will help you unload.
Yes. Tell us the unit number, which driveway and roller door to use, and where your strata allows a bin to sit. If the metal has to come out over the street frontage rather than through a rear yard, say so when you book, because overhead powerlines along the road limit where a hiab can lift.
No, and be wary of any list that claims to be current. Rates are per kilogram, set by grade and the market on the day, so we quote each load from a photo and confirm it on the scale in front of you.
Yes. Pick ups for refits and strip-outs run 24/7, so racking, shopfront framing, cable and old aircon can leave at night or on a weekend while the floor stays open. Aircon units have their refrigerant recovered before they are loaded.
No, we do not accept gas cylinders. Keep them out of any metal bin you fill for us, and arrange their disposal through a commercial waste service, since Community Recycling Centres only take household quantities.
Pick-up areas
We collect from every Sydney suburb. These pages cover local rules and access in more detail.

Prepared by
The A-K Scrap Metal teamFamily-run metal recyclers · Mortdale, Sydney · since 2003This page is prepared by the A-K Scrap Metal team, the family-run metal recyclers at our Mortdale yard. Metal prices move with the markets, so we never publish rates online. Call 0403 172 170 or send a photo for today's price.
Last updated A K Scrap Metal Traders Pty Ltd · ABN 49 144 672 908How we prepare our pages
Book a pickup
Book a pickup and let us handle the heavy lifting.